Dandie Dinmont Terrier Breed Magazine - Showsight

LENGTH, SHAPE & TOPLINE IN THE DANDIE DINMONT TERRIER

BY SANDRA PRETARI HICKSON

B ecause length, shape, and topline are the most misun- derstood areas of our Breed Standard and, consequent- ly, of our breed, it is where I focus most when giving our breed’s judges education presentation. I start there, I end there, and we revisit it over and over again throughout the presentation. The three are intertwined, and when judging “goes off” in our breed, this is invariably where it does; judges thinking that more is better or that any old curve in any old place or any topline at all will do. All, of course, are equally incorrect. If you do not understand length, shape, and most importantly, topline in our breed, you will be completely lost judging it. The height of the Dandie is 8 to 11 inches at the top of the shoulder. Length from the TOP of the shoulder to the root of the tail is twice the height of the dog, less 1 to 2 inches, so a 10-inch Dandie should be 18 to 19 inches long. Let’s use the Skye Terrier as a comparison. The Skye Terrier Standard calls for a Skye to be twice as long as it is tall; a 10-inch dog would be 20 inches long. However, that measurement is taken from the CHEST BONE, the PROSTERNUM, not from the TOP of the shoulder as is the Dan- die. Using this as an example, the average Dandie should be as long as the average Skye, but generally is not. And while the Skye Terrier does not have a problem maintaining its length of body, the Dan- die very much does. Length is very difficult to achieve and main- tain in a Dandie, and consequently, must be coveted and rewarded. When first looking at a class of Dandies, your immediate impression should be one of great length, and in the end, all things being equal, the longer of the two dogs must go up. I always get asked if a Dandie can be too long and the short answer is, “No, I’ve never seen it.” Now, if you have a Dandie come into your ring

that is longer than the Standard calls for, that Dandie would be too long. However, as I have just said, I have never seen one and I have measured and examined hundreds of Dandies. Consequently, in a nutshell and to borrow the mantra from the Pembroke Welsh Corgi Judges’ Education presentation, “long is good, short is bad!” Our Standard is very clear about what the outline and topline of a Dandie should be, and it is as follows: “ The topline is rather low at the shoulder, having a SLIGHT downward curve and a corresponding arch over the loin, with a VERY SLIGHT gradual drop from the top of the loins to the root of the tail. ” [EMPHASIS added.] The downward curve is SLIGHT, ergo, the corresponding arch over the loin is also SLIGHT, with the VERY SLIGHT drop over the croup. In looking at the drawing below from our Illustrated Standard , you will see that the degree of arch over the loin very much mirrors the degree of downward curve at the shoulder, both are SLIGHT. No exaggerated curves, no camel backs, no roaches, no swamp backs—all are seen quite often being rewarded in the ring, along with the equally egregious ski slope/ stern high topline. Additionally, the rise must be over the loin, with the apex of the rise being over the center of the loin and not drift- ing forward towards or in the middle of the back, both of which are quite common. The above-described toplines are not only incorrect but almost always denote weakness, not only of the topline but in other areas as well. A Dandie with a roached and/or camel back is almost always short in body and straight in front, with little to no proster- num. A Dandie with a ski slope topline is almost always straight in the rear and, of course, would not have the required very slight drop from the top of the loin to the root of the tail. And so it goes.

306 | SHOWSIGHT MAGAZINE, DECEMBER 2022

Powered by